Contact Us

 

Shanghai Finzone Windows & Doors Co.,Ltd

Address:Room 1-506, No.615, Ningqiao Road, Shanghai, China

Contact:Alice Zhang

Tel:+86-21-50800521

Fax:+86-21-50320395

Mobile:+8617740863682

Email:finzone2001@gmail.com

           finzone08@gmail.com






Home > News > Content
Unframed Glass Door Has An Advantage May 10, 2018

The rimless glass door is almost completely transparent, so the lighting is good and can be used in any combination. Generally used in shopping malls, hotels, offices and other places.

The glass door is different from aluminum alloy door, plastic steel door and other common door the biggest characteristic, is its door fan (glass) has no fixed border around the edges. The frame glass door is commonly used 8~12MM toughened glass to make door fan, up and down use adornment frame or the clip is fixed directly, ground needs to be planted ground spring.

Installation step editing

1. The installation of fixed partition wall shall be carried out after the completion of other working procedures in the indoor area. Fixed partition and activity glass doors must be unified pay-off positioning, partition and glass doors of the positioning line according to the requirements of design drawings, determine frame position, to accurately measure the ground elevation and the frame at the top level.

2. Install the glass partition wall, the width of the limit slot at the top of the door shall be greater than the glass thickness of 2 ~ 4mm, and the groove is between 20 ~ 30mm, so that the glue can be filled. The installation method can be used to draw two metal decorative board edges from the centerline of the projectile, and then the installation of the limit slot at the top of the door frame by the border line. The wood cushion in the slot is deep. Increase or decrease the adjustment through the pad.

3. Install the metal veneer. The installation method can be used to nail the square wood on the original embedded wood brick, or the square wood is fixed on the ground by the expansion bolt, and then the metal trim panel will be glued to the wooden side with the universal glue. Aluminium alloy square tube, can be fixed on the frame column with aluminum Angle, or with wooden screw fixed in the wood brick on the ground.

4. Install the door frame. Press the centerline of the projectile to make the door frame square, and then use plywood to determine the shape and position of the frame column. (note that the trim size should be reduced.) Finally, outsource the metal decoration, and place the decoration in the middle position of the installation glass facing the head seam. Joint position must be accurate and vertical.

5. Glass installation. Use a glass sucker (or a glass sucker) to absorb the thick glass, then hold the suction cup and lift the thick glass plate from 2 to 3 people and move it to the installation site to be in place. Methods: foundation should insert frame at the top of the upper limit of the glass groove, and then put the bottom of the glass on tap to align the center line, and the installation location of good on both sides of the door frame, make the thick glass of two side just metal decoration face seam sealed doors, both inside and outside it invisible facing juncture.

6. Fixed glass. On tap wooden nail article two flat square inside and outside the thick glass caught in the middle, but from the plate glass need to set aside about 4 mm gap, and coating adhesive on the flat square bar will be facing plate sticking in the wood and two flat square bar.

7. Glass glue sealing. Glass glue is injected on both sides of the top root slot and on both sides of the bottom glass notch and the thick glass and the door frame column. The injection sequence should start from the end of a certain slit to the end of the end. Operation main point is: hold caulking gun pressing handle the strength should be uniform, at the same time, the speed of moving along the crack to uniform, namely as the glass glue out, moving at a constant speed injection gate, make glass glue in aperture place form a homogeneous linear. Finally, remove the excess glass glue with plastic and wipe with a clean cloth.

8. Connect the glass. Fixed part of the plate glass, because the width size is too big, must be assembled by two or more, two pieces of alignment stitching must form joint, butt seam should be 2 ~ 3 mm distance (glass incision for seam must be inverted). After the glass is fixed, want to use glass glue into the aperture, after filling, also want to use plastic sheet to make the glue smooth, make the seam to form a clean uniform line, the glass surface should use clean cloth to wipe the glue trace.


Previous: The Advantage Of Bridge Aluminum Window

Next: No Information